**Phoenix Pools: Is "Salt Water" Burning Summer Skin?**
By Franklin Everett ShawThe shimmering turquoise water beckons on a sweltering Phoenix afternoon. You dive in, expecting refreshing relief, but instead, you’re met with a slight stinging sensation. Could it be the saltwater pool you were so excited about?
It’s a common concern in the Valley of the Sun, where backyard pools are practically a necessity. Many believe saltwater pools are gentler than traditional chlorine pools, but the reality is more nuanced. Let’s dive into the science and separate fact from fiction, so you can enjoy your Phoenix pool without the itch.
Saltwater pools aren’t actually chlorine-free. They utilize a salt chlorine generator, which uses electrolysis to convert dissolved salt (sodium chloride) into chlorine. This means you’re still swimming in chlorinated water, just produced differently. The key difference lies in the type and concentration of chlorine.
Traditional chlorine pools often use chlorine tablets or liquid chlorine, which can contain stabilizers like cyanuric acid (CYA). High CYA levels can bind to the chlorine, making it less effective as a sanitizer and potentially irritating to the skin. Saltwater pools, when properly maintained, generally produce lower and more consistent levels of chlorine, often without the need for added stabilizers.
So, why the irritation? The culprit is often an imbalance in the pool’s chemistry.
Here’s a step-by-step guide to troubleshooting and preventing skin irritation in your Phoenix saltwater pool:
Test Your Water Regularly: Invest in a reliable test kit (liquid test kits are generally more accurate than test strips) and check your pool water at least twice a week. Pay close attention to:
- pH: Aim for a pH between 7.2 and 7.8. High pH can cause scaling and reduce chlorine effectiveness, while low pH can be corrosive and irritating.
- Chlorine: Maintain a free chlorine level between 1 and 3 ppm (parts per million). Too little chlorine allows bacteria and algae to thrive, while too much can irritate skin and eyes.
- Salt Level: Follow your salt chlorine generator’s manufacturer recommendations for the ideal salt level. Too little salt will prevent the generator from producing enough chlorine, while too much can damage the equipment.
- Cyanuric Acid (CYA): If you’re adding CYA to your saltwater pool (some generators require it), keep the level between 30 and 50 ppm.
Adjust Your Salt Chlorine Generator: Fine-tune your generator’s output to maintain the proper chlorine level. Start with the manufacturer’s recommended settings and adjust as needed based on your water testing results. Remember that Phoenix’s intense sun can deplete chlorine quickly, so you may need to increase the output during peak summer months.
Consider Calcium Hardness: Phoenix water is notoriously hard, meaning it contains high levels of calcium. High calcium hardness can lead to scaling on pool surfaces and equipment, which can also contribute to skin irritation. Aim for a calcium hardness level between 200 and 400 ppm. If your levels are consistently high, consider using a sequestering agent to prevent scaling.
Shock Your Pool Regularly: Even with a saltwater system, shocking your pool periodically is essential to eliminate combined chlorine (chloramines), which are the real irritants. Chloramines are formed when chlorine reacts with organic matter like sweat, sunscreen, and body oils. Use a non-chlorine shock (potassium monopersulfate) to avoid over-chlorinating your pool.
Rinse Off After Swimming: This is crucial in the dry Phoenix climate. Chlorine, even at optimal levels, can dry out your skin. Rinsing off with fresh water immediately after swimming helps remove chlorine residue and prevent dryness.
Moisturize, Moisturize, Moisturize: The Arizona desert is brutal on skin. Apply a generous amount of moisturizer after showering, focusing on areas that are prone to dryness, such as your arms, legs, and face. Look for moisturizers containing ingredients like hyaluronic acid, ceramides, or shea butter.
Choose the Right Sunscreen: Sunscreen is a must in Phoenix, but some sunscreens can react with chlorine and contribute to chloramine formation. Opt for mineral-based sunscreens containing zinc oxide or titanium dioxide, as they are less likely to cause problems. Apply sunscreen at least 15 minutes before entering the pool and reapply every two hours, or more frequently if you’re sweating or swimming.
Consider a Saltwater Conditioner: Products like “Salt Cell Saver” can help extend the life of your salt chlorine generator and improve its efficiency. They work by reducing scaling and corrosion on the cell plates.
Check Your Pool’s Circulation: Proper circulation is essential for distributing chlorine evenly throughout the pool and preventing stagnant areas where bacteria and algae can thrive. Ensure your pump is running for at least 8 hours per day, and that your skimmers and returns are properly positioned.
Clean Your Salt Cell Regularly: Over time, calcium and other minerals can build up on the salt cell plates, reducing its efficiency. Follow the manufacturer’s instructions for cleaning your salt cell, typically involving soaking it in a diluted muriatic acid solution.
Common Pitfalls and How to Avoid Them:
- Ignoring Water Chemistry: This is the biggest mistake. Neglecting regular water testing and adjustments is a recipe for irritation and other pool problems.
- Over-Reliance on the Salt Chlorine Generator: Salt chlorine generators are not a “set it and forget it” solution. They require regular monitoring and adjustments to maintain proper chlorine levels.
- Using the Wrong Type of Shock: Chlorine shock can exacerbate skin irritation, especially if used excessively. Opt for non-chlorine shock instead.
- Not Rinsing Off After Swimming: This allows chlorine to linger on your skin and cause dryness and irritation.
- Forgetting to Moisturize: The dry Phoenix air will quickly suck the moisture out of your skin, making it even more susceptible to irritation.
Real-World Scenario:
Let’s say you live in Scottsdale and have a saltwater pool. You’ve noticed that your kids are complaining of itchy skin after swimming. You test your water and find that your pH is high (8.0) and your chlorine level is low (0.5 ppm). You also notice some scaling on your pool tiles.
Here’s what you should do:
- Lower the pH: Add a pH reducer (sodium bisulfate) to bring the pH down to the 7.2-7.8 range.
- Increase Chlorine Production: Adjust your salt chlorine generator’s output to increase chlorine production.
- Shock the Pool: Use a non-chlorine shock to eliminate chloramines.
- Clean the Salt Cell: Inspect your salt cell for scaling and clean it if necessary.
- Consider a Calcium Hardness Reducer: If your calcium hardness is high, use a sequestering agent to prevent further scaling.
- Encourage Rinsing and Moisturizing: Remind your kids to rinse off with fresh water after swimming and to apply moisturizer.
By following these steps, you can restore your pool’s water chemistry and eliminate the source of irritation.
Saltwater pools in Phoenix can be a fantastic way to beat the heat, but they require diligent maintenance and attention to detail. By understanding the science behind saltwater chlorination and following these practical tips, you can enjoy your pool comfortably all summer long, without the itch. Remember, a little effort goes a long way in creating a healthy and enjoyable swimming experience for you and your family.